C ameraLink CameraLink is a method of serialising parallel data that made it straightforward for manufacturers of digital cameras and framegrabbers to add a ChannelLink chip to existing LVDS devices to make them Cam eraLink devices. The CameraLink standard defines three levels of bandwidth:
Base – which uses a single ChannelLink chip to give 225M B /s over a single cable
Medium – which uses two chips to make 450MB /s over two cables
Full – three ChannelLink chips giving upto 675M B /s over two cables In addition to the image data the cables also carry serial data, CameraLink framegrabbers emulating a serial port on the PC in which they are installed.
The cables themselves are somewhat bulky by modern standards and are terminated on both ends by an MDR26 connector. The original standard came out in 2000. In 2007 there were developments to create Mini - CameraLink using an SDR 26 connect or and als o Power over CameraLink (PoCL). The transmission distance is limited by the nominal 10m cable limit, although it is possible to extend this in some cases. Good quali ty cables and low pixel clock values can take this fu rther (as far as 18m) but larger increases can be made with CEI ’ s Bit M axx cables that add pre - emphasis and equalisation to give up to 25m for base C ameraLink .
Much longer distances can be achieved using either a repeater such as the Phrontier CLEVER or a fibre - optic converter such as the Phrontier PHOX , see Figure 1.
The advent of Gigabit Ethernet- based cameras (1000BaseT) and then the GigEVision standard has allowed a revolution in the way machine vision cameras can be used, taking advantage of network topologies and cable lengths. Ethernet allows 90m between links – where a link is a switch, for example. Network topologies allow many cameras into one PC in a way tha t quickl y becomes impract ical for a framegrabber - based system. Also it is possible to multi - cast data from a camera, so instead of being a si n gle point to single point connection, one camera can serve data to multipl e PCs , s ee Figure 2. A major advantage to the use of ethernet cameras is the capability to re - send data that is lost in transmission.
The restriction for GigE is bandwidth . T he DALSA Genie HM models make full use of GigE , for example 640x4 80 pixels, 8bi t s per pixel at around 3 00frames/second. But with colour, high resolution or multiple cameras it is easy to run out of bandwidth on a single network interface. While 10GigE is beginning to arri ve, it is expensive and not yet widespread . However, the concept of Link Aggregation Groups ( LAG, also known as teaming) where GigE links are combined into a larger logical link made up of multiple links. T he AVT GX range make use of this to allow high resol ution and high bit - depth images without sacrifi cing frame - rate, see Figure 3.
The GigE Vision standard b uilds on the Genicam standard, which requires cameras to describe themselves with an xml file. This seemingly simple point means that camera configura tion files are no longer needed as the camera can describe its parameters (such as image size, format and so on) . It also means that the camera can let a system know its capabilities such as allowable sh utter times, gain values etc. The standard describes some standard fea tures but allows for extensions so that any feature can be covered by the standard purely by including it in the camera ’ s xml file.
Although CameraLin k is a high - throughput standard, there are still devices that output more data than can be supported by CameraLink Full ’ s 675Mb/s. Some cameras and frame grabbers have used the so - called CameraLink Full 10tap mode to extend the CameraLink standard slightly, for example the Silicon Software microEnable IV AD4 - CL grabber with on - board FPGA for processing. CameraLink HS is close to a specification release and extends the capabilities of CameraLink w ith more bandwidth, longer and simpler cables. The bandwidth scales between 300Mb/s ( between CL Base and Full) and 6 Gb/s (around nine times the bandwidth of CameraLink Full). In addition it incorporates Genicam to allow self - describing cameras . A competit i ve standard is CoaXpress using c oaxial cables to allow 100m cable lengths and upto 6.25Gb/s bandwidth The advent of USB 3.0 as a consumer interface has also allow e d greater bandwidth to be exploited. USB 3.0 is ten times faster than USB 2.0, giving up to 5 Gb/s , can provide more power ov er the bus but is likely to be highly cable - length dependent.